Trending Products Most Expensive 3d Printer - Print material-exquisite white-8006 – Digital Manufacturing
Trending Products Most Expensive 3d Printer - Print material-exquisite white-8006 – Digital Manufacturing Detail:
3D Printing Materials
Exquisite white-8006
Introduction of 3D Printing Materials
Characteristics
SZUV-W8006??
PRODUCT DESCRIPTION?
SZUV-W8006?is an ABS like SL resin which has accurate and durable features. It is designed for solid state SLA platforms.?SZUV-W8006?can be applied in master patterns, concept models, general parts and functional prototypes in the?field of automotive, medical and consumer electronics industries.The parts duability building with SZUV-W8006?is over 6.5months.SZUV-W8006
TYPICAL FEATURES
-Liquid resin`s medium viscosity, so easy recoating, easy clean parts and machines
-Improved strength retained, improved dimensions retention of parts in humid condition
-need minimal part finishing
-Long shelf life in machine
TYPICAL BENEFITS
-Need less part finishing time,easier post-curing
-Buliding accurate and high tough parts with an improved dimensional stability
-High quality controls for vacuum casting parts
-Low shrink and good resistance to yellowing
-Magnificent white color
-Outstanding machinable SLA material
Physical Properties – Liquid Material?
Appearance | White |
Density | 1.13g/cm3?@ 25 ℃ |
Viscosity | 376?cps @ 27?℃ |
Dp | 0.148?mm |
Ec | 7.8?mJ/cm2 |
Building layer thickness | 0.1mm |
?Mechanical Properties of Post-Cured Material?
MEASUREMENT | TEST METHOD | VALUE |
90-minute UV post-cure | ||
Hardness, Shore D | ASTM D 2240 | 87 |
Flexural modulus, Mpa | ASTM D 790 | 2,592-2,675 |
Flexural strength, Mpa | ASTM D 790 | 70- 75 |
Tensile modulus, MPa | ASTM D 638 | 2,599-2,735 |
Tensile strength, MPa | ASTM D?638 | 39-56 |
Elongation at break | ASTM D 638 | 13?-20% |
Poisson`s Ratio | ASTM D 638 | 0.4-0.43 |
Impact strength notched Izod, J/m | ASTM D 256 | 35?- 45 |
Heat deflection temperature, ℃ | ASTM D 648 @66PSI | 62 |
Glass transition,Tg,℃ | DMA,E”peak | 73 |
Coefficient of thermal expension, /℃ | TMA(T<Tg) | 95*E-6 |
Density, g/cm3 | 1.16 | |
Dielectric Constant?60 Hz | ASTM D 150-98 | 4.6 |
Dielectric Constant?1 kHz | ASTM D 150-98 | 3.9 |
Dielectric Constant?1 MHz | ASTM D 150-98 | 3.6 |
Dielectric?StrengthkV/mm | ASTM D 1549-97a | 14.9 |
?Note: the temperature of szuv-w8006 should not be too high. Please use it below 25c.Recommended temperature for use and preservation is 18-25 ℃
Fire Fighting Measures
(1) extinguishant
?Dry powder fire extinguishing agent, alcohol resistant foam extinguishing agent, carbon dioxide, dry sand, spray water.
(2) Special risk
?Fires may produce irritation and harmful gas
(3) The firemen of protective measures
?Fireman should wear protective appliances (eye protection, protective clothing, mailing gas with gas mask, etc.), put out the fire in the windward.
6.?Accidental Release Measures
(1) Homework personnel protective equipment
?Ensure adequate ventilation, wear suitable protective clothing, make a good job in hand and eye/face protection.
(2) Environmental protection measures
?Prevent products from entering the drain or open water
(3) Cleaning method
?For a small amount of leakage, use dry sand, soil and towels absorb the residual liquid, recycling and airtight container.
?For a large number of leakage, leakage of liquid can be in front of the embankment, the introduction of recycle to safe place.
(4) Secondary hazard prevention measures
?Quickly remove all fire spark (ban on smoking in nearby, and the ignition).
7.?Handling And Storage
(1) Operation treatment technical measures
?Avoid contact with eyes, skin and clothing. Don’t inhaling mist or steam, don’t accidentally swallow, keep container tightly closed after the thorough cleaning.
(2) Partial or full ventilation???Maintain adequate ventilation
(3) Safe handling matters needing attention???No?smoke, no fire
(4) Safe storage conditions
?Stored in a cool, well ventilated place, away from heat, sparks and flames. Keep container tightly closed until it is put into use.
(5) packaging container and material
?In the process of custody, please do not transfer to other containers. Don’t fall back to the original containers of products that will be used.
Cases
SOME OF MY PROJECTS
Education
Rapid prototype
Auto Parts
Constructional design
Art Design
Medical
Product detail pictures:
Related Product Guide:
Autodesk Creates Design-to-Print Workflow for HP and GE 3D Printers | 3d Printers Suppliers In Cape Town
$ 1.1 billion Opportunity by 2024 in the Additive Manufacturing with Metal Powders Market: Global Key Vendors | 3d Printers Suppliers In Cape Town
Fast and very good quotations, informed advisers to help you choose the correct merchandise that suits all your preferences, a short creation time, responsible excellent command and different companies for paying and shipping affairs for Trending Products Most Expensive 3d Printer - Print material-exquisite white-8006 – Digital Manufacturing , The product will supply to all over the world, such as: Liberia, Libya, Florence, Relying on superior quality and excellent post-sales, our products sell well in America, Europe, the Middle East and South Africa. We are also the appointed OEM factory for several worlds' famous products brands. Welcome to contact us for further negotiation and cooperation.
By Gemma from Naples - 2016.01.28 18:53
Wide range, good quality, reasonable prices and good service, advanced equipment, excellent talents and continuously strengthened technology forces,a nice business partner.
By Emily from Lyon - 2016.11.12 12:31